Category: 

What Is Unfaced Insulation?

Unfaced insulation is not covered with a vapor barrier on either side.
Spray foam insulation increases energy efficiency.
Article Details
  • Written By: D.M. Abrecht
  • Edited By: Lucy Oppenheimer
  • Last Modified Date: 24 August 2014
  • Copyright Protected:
    2003-2014
    Conjecture Corporation
  • Print this Article
Free Widgets for your Site/Blog
Mickey Mouse was the first non-human to win an Oscar.  more...

September 20 ,  1873 :  The Panic of 1873 caused the New York Stock Exchange (NYSE) to shut down.  more...

Unfaced insulation is a blanket insulation product, usually made of fiberglass, but sometimes made of cotton, sheep's wool, mineral wool, plastic, or other materials. It differs from faced insulation in that it is not covered with a vapor barrier on either side. The "facing," therefore, refers to the vapor barrier on the insulation.

Having a well-insulated home results in lower energy bills and prolongs the life of heating and cooling equipment. Insulation can also serve as a acoustic barrier, keeping sound from penetrating walls. Several options exist for the builder or homeowner looking to insulate the walls and attic of a structure. Loose-fill and spray foam insulation are sprayed into place, usually by a professional, and completely fill the space where they are applied. Blanket insulation, which includes both faced and unfaced types, is usually pre-cut into rolls or rectangular segments called batts. It is sized to fit into the standard 16- or 24-inch (about 41- or 61-cm) spaces between studs.

Blanket insulation is cheaper than other options and can usually be installed by the homeowner. Its uniform thickness helps ensure a consistent R-value — insulation effectiveness &mdsash; throughout the area it is used. Since it does not completely fill the target space like loose-fill or spray foam, care must be exercised during installation in order to guarantee that all gaps are filled. Otherwise, heat could escape.

Ad

Blanket insulation can be faced on one side, faced on both sides, or unfaced. Faced insulation is covered on one or both sides with a vapor barrier, usually made of plastic, foil, or asphalt-coated paper. The purpose of the vapor barrier is to keep moisture out of the walls of the home. When one-sided faced insulation is installed, the vapor barrier is left facing toward the living space.

Unfaced insulation comes without a vapor barrier. It may be used with a separate vapor retarder. That separate vapor blocker may be a vapor-retarding paint or sheets of plastic or foil sold specially to help block moisture in conjunction with insulation. The combination of unfaced insulation and a separate vapor retarder is believed to create a more effective barrier against moisture than faced insulation alone.

Unfaced insulation may be used in renovations where new insulation is applied on top of old insulation. If both the new and old insulation have vapor barriers, then moisture may become trapped between the layers of insulation, damaging it. In this situation, it's often best to let the old vapor barrier continue to do its job, and improve the R-value of the existing installation with unfaced batts or rolls.

Ad

More from Wisegeek

You might also Like

Discuss this Article

anon43140
Post 3

anon41525 I believe is mine. what i want to know is about insulating the area. should I use the crawl space insulation with no covering, just pink stuff, to keep the cold of winter from coming through the ceiling of the shop/floor of my dining room?

anon41525
Post 2

I think I have what would be considered an unvented crawl space that has 7' ceilings. It is a walk out basement that is used to store lawn stuff. it is not heated. My dining room is directly above and is very cold so I installed insulation in the ceiling -- pink stuff up and paper down so when in the room I can read the writing. I now have rain in the "shop" and scary white lifeless spiders The insulation is wet and causing puddles on the floor. Should I get a mask and rip it out? help.

frankjoseph
Post 1

The greater the R-value, the greater the insulation effectiveness. Some common R-values include R-13, R-19, and R-30.

Post your comments

Post Anonymously

Login

username
password
forgot password?

Register

username
password
confirm
email