Category: 

What is SATA or Serial ATA?

SATA cable connected to a drive.
SATA cable.
Article Details
  • Written By: R. Kayne
  • Edited By: L. S. Wynn
  • Last Modified Date: 15 July 2014
  • Copyright Protected:
    2003-2014
    Conjecture Corporation
  • Print this Article
Free Widgets for your Site/Blog
Doorknobs made of brass automatically disinfect themselves in less than 8 hours.  more...

July 24 ,  1979 :  Serial killer Ted Bundy was found guilty of first-degree murder of two female college students.  more...

SATA or Serial ATA (Advanced Technology Attachment) is the next generation drive interface, following the traditional Parallel ATA (PATA).

Anyone who has peered into a computer is familiar with the flat, 40-wire parallel cables that connect the hard drive, CDROM and other devices to their controllers. PATA has been the standard and has served well, but it has also had drawbacks. Cables limited to 18 inches (46 cm) in length often made connections difficult and also clogged cases blocking airflow, while cooling has become crucial. Though rounded cables became available, the most advanced PATA drives (Ultra ATA/133) hit the maximum parallel transfer rate of 133 MB/ps. With the speed of CPUs, RAM and system buses improving, designers saw PATA would soon be bottlenecking advanced drive efficiency in system architecture.

Enter SATA.

Serial ATA has distinct key advantages over its predecessor. Cables are very thin with small 7-pin connectors. They can be up to 3 feet (1 meter) in length, and are easily routed to stay out of the way allowing maximum airflow inside the case. SATA also has a far lower power requirement of just 250 mV compared to PATA's 5-volt requirement, and with chip core voltages declining, this speaks well of SATA's future. Serial ATA does away with Master/Slave configurations and drive jumpers. Setup is greatly simplified, and the technology even allows hot-swapping, meaning drives can be removed or added while the computer is running.

Ad

However, the most promising feature of Serial ATA is that it eliminates the transfer limit hit by PATA. First generation has a maximum transfer rate of 150 MBps, and second generation SATA delivers about 300 MBps. A third generation SATA set for 2009, "SATA 6Gb/s" will deliver roughly twice the speed of the previous SATA iteration.

With introductory transfer speed so close to existing Ultra ATA/133 speeds, the increase in real-world performance is negligible for first generation SATA, though prices of the drives are comparable to PATA drives, making the switch to the new technology a good choice when upgrading, building, or buying a new system. Motherboards with integrated SATA and PATA interfaces are widely available to accommodate both types of drives, and there are no restrictions to using both types in the same system. Serial ATA is also a good choice for RAID and is earmarked to eventually replace PATA.

For older systems, third party SATA controllers can be placed in any PCI slot, should you purchase a SATA drive. (A parallel Ultra ATA drive can also be used via a PATA-to-SATA adapter, though drive performance will take a hit, as the adapter must translate the data stream from parallel to serial.)

If upgrading your motherboard, buying SATA-enabled will allow ease of use for future SATA drives even if your current drives are standard ATA.

Note: When using some third party devices or adapters support for hot-swapping may be lacking or "quirky." It is always wise to backup valuable data before risking loss.

Ad

Discuss this Article

anon247496
Post 22

Thanks for "Wise" tutorials! --Bogdan

anon173996
Post 21

who is the inventor of SATA?

anon149382
Post 20

Please someone, give me answer. If sata and pata HDD used in conjunction, then will both hdd work at different speeds or the lower speed from them?

anon96584
Post 17

what is USB3?

anon67951
Post 15

Thanks a bunch. Clear now.

anon61673
Post 14

Thank you. It really makes sense now.

anon57990
Post 13

Cool. A clear, simple explanation of SATA. Thank you. J White

anon38068
Post 12

Heaven help me - The principles of KISS are completely gone ... what happened to SIMPLE?

bennyg14
Post 11

To anon15376:

Go to newegg and search for 2.5" enclosure for SATA HD.

You can't make mistakes with newegg, they are the best. you don't have to buy the most expensive however check in the spec that the enclosure supporting SATA HD and today it will be helpful to buy enclosure that supporting eSATA (external SATA) in additional to the USB interface.

bennyg14
Post 10

to wcolligan,

you should go to administrative tools in the control panel, Computer management, disk management and rename drives letter to be continuous.

Be careful when doing it and try not to change the HD's letters if you are not enough skilled.

To change the letter you should click with the right mouse button on the DVD drive you want to change and choose change letter.......

Good luck

wcolligan
Post 9

I have a new computer and I have installed 2 SATA DVD drives. Hardware manager says that windows cannot load the drivers because there is a duplicate device present. I can disconnect one of the drives and windows recognizes the one drive. I cannot get windows to recognize bothe drives together.

Bill

anon15376
Post 8

I have a Seagate Momentus 7200 hard drive that was in my HP DV9000 laptop. It crashed, and I got it replaced. I want now to see if I can get any data off it. The drive is a Serial AT. Is there an external enclosure that can house the drive?

An eSATA will not work. It is an internal drive -- can I even house it in an external enclosure? Thanks!

anon10872
Post 7

If I have a motherboard with both Pata and Sata sockets can I use 4 hardrives ie 2 Ata and 2 Sata?

shuper30
Post 6

When I booted up my DELL DIM 4600 computer, I got this message: Invalid configuration information - please run SETUP program. I hit F2 to run the setup program and in the drive configuration, among others, the SATA Primary Drive, SATA Secondary Drive, Primary Slave Drive are set on OFF. Should these be ON?

anon8908
Post 5

Whats the cost of a pata/sata adapter?

anon5194
Post 4

The jumper block adjacent to the SATA interface connector on SATA 300MB/s drives can be used to force the drive into SATA 150MB/s mode for use with older SATA controllers that only work with SATA 150MB/s drives.

anon3065
Post 2

Will an SATA 300 hard drive work (and if so, how) in a SATA 150 connection?

Post your comments

Post Anonymously

Login

username
password
forgot password?

Register

username
password
confirm
email