Category: 

What Is PATA?

A computer motherboard.
Article Details
  • Written By: R. Kayne
  • Edited By: O. Wallace
  • Last Modified Date: 28 November 2014
  • Copyright Protected:
    2003-2014
    Conjecture Corporation
  • Print this Article
Free Widgets for your Site/Blog
On average, people spend a year of their lives looking for items they've misplaced.  more...

December 18 ,  1620 :  The Mayflower landed in Plymouth.  more...

PATA, also known as Parallel ATA (Advanced Technology Attachment), is a type of internal computer port that attaches to hard drives and other devices. It has been replaced by the faster, sleeker port technology known as Serial ATA, or SATA. Virtually all devices are now made to conform to the SATA standard.

Originally, PATA was known simply as ATA (pronounced by sounding out the letters). The ATA standard evolved into many flavors, with each subsequent type increasing data transfer rates. It wasn’t until the serial flavor of ATA came along that the original parallel standard became retroactively known as PATA.

PATA devices are easy to spot by the rather large 40-pin port that connects to a parallel ATA cable. These cables are flat, wide, ribboned cables with 40 parallel wires, hence the designation, parallel. Data is split among the lanes and travels in parallel between the PATA controller and the connected device in a master/slave configuration. Cables later increased to 80-wires in order to break through a data transfer ceiling hit with the 40-wire flavor of parallel ATA known as ATA/33. The first 80-wire iteration was ATA/66 with a theoretical maximum data transfer rate of 66.6 megabytes per second (MBps), or twice that of ATA/33.

Ad

The cables have a maximum length barrier of 18 inches (46 cm), and require 5 volts of power. One side of a PATA cable features a red line to indicate the layout for pin one, useful when connecting the cable to a compatible device. PATA’s death, however, was that it hit a data transfer ceiling at 150 MBps.

SATA cables can be up to 3 feet (1 meter) in length, are very narrow, and only require 250 millivolts of power. The first release of SATA was as fast as ATA/150 (150 MBps), but used only a fraction of the power required by PATA while also allowing more airflow through case. SATA II pushed the data transfer rate to 300 MBps, and more specifications have followed. Older motherboards that only have PATA slots can run SATA devices by using a third-party SATA controller that will fit into the slot, thus allowing an upgrade to SATA without upgrading the motherboard.

During the interim switch to SATA, motherboards generally featured both types of ports and controllers. One PATA port can control up to two legacy parallel devices. SATA uses peer-to-peer technology, (rather than master/slave), so one of its ports controls one device. Motherboards are made with multiple SATA ports for accommodating generous amounts of data storage and optional RAID configurations. SATA devices are also hot-swappable, unlike PATA devices.

Ad

More from Wisegeek

You might also Like

Discuss this Article

anon89286
Post 6

thanks a lot for such an easy explanation, but i would like to say something, that it would be better if anyone describes SATA more.

anon77648
Post 5

what is the meaning of serial Ata -- does this mean sata hard disk?

anon61785
Post 4

I find that it's best to talk to people like a six year old when you are discussing techy stuff.

After all the purpose is to communicate information and knowledge and facilitate understanding, not impress others as to how smart you are with acronyms, jargon and double-jointed words.

anon37519
Post 3

Is PATA the same as ATA-6?

anon8339
Post 1

Very good and informative, simple language- even computer dummy like me could understand.

Post your comments

Post Anonymously

Login

username
password
forgot password?

Register

username
password
confirm
email