Category: 

What is Dielectric Strength?

Article Details
  • Written By: Paul Scott
  • Edited By: R. Halprin
  • Last Modified Date: 17 September 2016
  • Copyright Protected:
    2003-2016
    Conjecture Corporation
  • Print this Article
Free Widgets for your Site/Blog
Due to synthetic materials and furnishings, new homes burn about five times faster than those built 30 years ago.  more...

September 25 ,  1789 :  The US Bill of Rights was adopted.  more...

Dielectric strength is an engineering term that refers to the maximum voltage an insulating material can withstand before breaking down or failing. This is a definitive characteristic of insulation materials and is used to grade new types or test the integrity of existing installations. Dielectric strength tests typically consist of exposing insulators to short duration, high voltage values while scanning for leakage or insulation breakdown. The voltages used to test the dielectric strength of insulators usually range from 5,000 to 400,000 volts (5–400 kV). Oils used as insulators in transformers and switchgear are checked by tapping a small sample and testing it in a specialized test rig.

Insulation breakdowns are a major cause of electrical failures and accidents which cause millions of dollars of damage and many, often fatal, injuries every year. Establishing the integrity or dielectric strength of insulating elements is an important part of any electrical installation's maintenance regimen. It is also a critical part of the development of new insulating materials. The dielectric strength of any insulator is the maximum voltage it can withstand without failing. This is established by exposing the insulating material to very high voltages in an environment where leakages or breakdowns of the insulation are accurately measured.

Ad

Also known as hipot testing, dielectric strength testing is carried out by a wide selection instruments with differing capacities. These range in size and output values from small bench top units capable of generating test voltages of 5 kV to large installation testers which can have outputs of 400 kV or more. Insulation testers may feature alternating current (AC) or direct current (DC) outputs with current values ranging from approximately 10 mA to 400 OVA. Specialized testers are also available which can test the breakdown values of fluid samples taken from transformer and switchgear oil baths.

The testing of insulating oil is particularly important because the dielectric strength of these fluids are subject to many environmental variables such as moisture and carbon contamination. Moisture in insulating oil is a major problem caused by the condensation of airborne moisture inside the transformer casing. Only small amounts of moisture are necessary in a large transformer's oil bath to cause a catastrophic failure. For this reason, regular tests should be carried out to establish the dielectric strength of switchgear and transformer oil. Solid insulators such as the PTFE sheaths on high tension cables can also degrade with time; exposure to ultraviolet radiation, chemicals, and lubricants or excessive heat and should be tested regularly to ensure their integrity.

Ad

You might also Like

Recommended

Discuss this Article

SkyWhisperer
Post 3

@everetra - Unfortunately, you have described a reality that tends to be more common than it should be.

I remember seeing a picture of a substation fire. It was an extreme amount of electricity, and you could see several successive photos where large electric arcs were forming above the substation, (kind of like a Tesla’s coil) before the fire engulfed it.

I don’t know what the voltage range was for the dielectric testing of insulating equipment in the utility industry, but I would venture to guess that someone didn’t properly test that substation equipment.

everetra
Post 2

It appears from the article that in order to really test the dielectric levels of insulators, the voltages have to be pretty high.

I imagine then that you could have a situation with a poorly insulating material, but which didn't break down because there was never a large enough spike in voltage to create a problem.

This would create a ticking time bomb, in my opinion. These materials would be inherently defective, in that sense, but the defects would not show up unless they hit a really huge spike in voltage.

allenJo
Post 1

Dielectric strength is a concept I remember back in the good old days when I was an electronics hobbyist.

I used to build circuits and the components would have various resistance levels. Capacitors, in particulars, were defined by their electrical charge and their dielectric strength. The plates that separated the capacitors provided resistance and the net effect was that it would increase the capacitance of the component.

Post your comments

Post Anonymously

Login

username
password
forgot password?

Register

username
password
confirm
email