Category: 

What is Blown Insulation?

Article Details
  • Written By: Koren Allen
  • Edited By: Jay Garcia
  • Last Modified Date: 28 June 2015
  • Copyright Protected:
    2003-2015
    Conjecture Corporation
  • Print this Article
Free Widgets for your Site/Blog
Beavers have transparent eyelids as well as nose and ear valves that automatically close underwater.  more...

July 1 ,  1979 :  The first Sony Walkman was sold.  more...

Blown insulation, also called loose fill insulation, is commonly used to insulate existing structures that previously had no insulation, or where additional insulation is needed. It is made up of loose particles which are blown into an attic or into wall cavities, which are the spaces between the interior and exterior walls of a building. Since even distribution of the material is important, and because special pneumatic equipment is required, installation is usually done by a professional.

There are three basic types of blown insulation commonly available. Fiberglass insulation consists of small particles of spun glass fibers. Mineral wool is made from particles of rock or steel slag, which is a recycled manufacturing waste. Cellulose insulation comes from recycled newspapers or cardboard which has been treated with chemicals to make it resistant to flame and insects.

In the U.S., all insulation is given an R-value, which is a measurement of thermal resistance. Insulation with a higher R-value provides more effective barriers against heat loss. R-values are based on the type of material used, as well as thickness and density of the material. The R-value for blown insulation depends on which type is used, as well as how much is blown in; its thickness is measured with a ruler. Blown insulation often has two R-values. The first represents its value at installation, and the second represents a lower value after the material has settled over time.

Ad

Using blown insulation has many advantages. It is fairly economical, and is much easier to install in hard-to-reach areas, as well as working around obstacles such as chimneys or stove vents. Blown insulation is eco-friendly because it makes use of recycled materials. It can be used as the primary type of insulation, or it can be added to other types of insulation to help fill in the gaps and provide an additional heat barrier.

Blown insulation does have some disadvantages as well. Over time, the particles settle, which reduces its R-value. Sometimes it is mixed with adhesive before being blown in; the adhesive helps the particles resist settling. There are some concerns about blown insulation entering the living space through gaps in the home's ductwork, and the inhalation dangers of the fine particles are unknown. With a proper professional installation, many of these concerns can be alleviated. Since blown insulation has a tendency to absorb moisture, a vapor barrier should be used, particularly on a new installation.

Be sure and check on your locality's building codes and regulations. In the U.S., the National Electric Code (NEC) forbids blown insulation in older homes with certain types of outdated wiring systems, because overheating wires can create a fire hazard. Your installation professional will be able to advise you on the best type of insulation for your particular structure. As with all insulation products, you should avoid attic vents and heat-producing obstacles such as light fixtures.

Ad

You might also Like

Recommended

Discuss this Article

Sporkasia
Post 3

After reading this article and other articles about the different types of attic insulation, I am leaning toward the spray insulation. My problem with the fiberglass batts is that they are so difficult to work with in the close places and around objects as mentioned in this article. The batts are also terrible to clean up if you ever have a major leak in the attic.

The blown insulation sounds like it has many good characteristics, but I do not like that it can be blown about, and as the article says, the particles could enter the duct work. With the spray foam you can easily spray the insulation on the sides and on the top of the attic ceiling where the foam will stick. Also, you do not have the same worries about moisture damaging the insulation with the spray.

Drentel
Post 2

@Animandel - I think fiberglass insulation is generally safe. It's not as if fiberglass contains asbestos or some other known cancer causing substance. Any type of insulation has it's potential health drawbacks, as do other household products you use everyday. What I like about using blown insulation is that the installation process is so much simpler and quicker than putting down those batts.

Animandel
Post 1

We have always used the fiberglass batts to insulate our attics. However, since I have been reading about the potential dangers of the fiberglass, I have been looking for other types of insulation. A friend told me I should look into getting blown-in cellulose insulation.

The cellulose sounds like it might be a good alternative to fiberglass since the cellulose is made from old recycled newspapers. I like recycling, and newspapers shouldn't present any added health risks. However , I am a little concerned now that I read the part of the article that mentions the chance of breathing in the fine particles.

Post your comments

Post Anonymously

Login

username
password
forgot password?

Register

username
password
confirm
email